ITM ENGINE COMPONENTS : 5M9550 |
Crankshaft Main Bearing |
|
ENGINETECH : BC116J |
Crankshaft Main Bearing |
|
SEALED POWER : 7411MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
- Undersize mm: 0.25 ;
|
MAHLE / CLEVITE : MS2245A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2245H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS1702A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC119J |
Crankshaft Main Bearing |
|
SEALED POWER : 7011MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
- Undersize mm: 0.25 ;
|
MAHLE / CLEVITE : MS2006A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC485J |
Crankshaft Main Bearing |
|
ITM ENGINE COMPONENTS : 4M9516 |
Crankshaft Main Bearing |
|
SEALED POWER : 7245MA |
Crankshaft Main Bearing |
- Design Feature 2: Full flange thrust brg. ;
|
SEALED POWER : 7445MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
- Undersize mm: 0.25 ;
|
MAHLE / CLEVITE : MS2302A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : IROX7455MA |
Crankshaft Main Bearing |
- Country of Origin: US ;
- Package Dimensions: 3.375 x 1.237 x 6.750 inches ;
- Package Quantity: 1 ;
- Package Weight: 0.92 lb ;
- UPC: 019826113184 ;
|
MAHLE / CLEVITE : MS2223P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7440M |
Crankshaft Main Bearing |
- Part Material: Steel backed overplated bronze alloy ;
- Undersize mm: 0.25 ;
|
ENGINETECH : BC212J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2269HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2269H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 148M |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2007H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC470J |
Crankshaft Main Bearing |
|
ENGINETECH : BC393J |
Crankshaft Main Bearing |
|
ENGINETECH : BC202J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2007A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2259A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7292MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
|
MAHLE / CLEVITE : MS2007P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC209J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2292A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7461MA |
Crankshaft Main Bearing |
- Country of Origin: US ;
- Package Dimensions: 6.81 x 5.13 x 2.13 inches ;
- Package Quantity: 1 ;
- Package Weight: 1.67 lb ;
- UPC: 019826223845 ;
|
ITM ENGINE COMPONENTS : 5M1523 |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2292H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2292HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC384J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2344A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC206J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2314A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2203A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC428J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2350A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2384A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2334HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2334HC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2334H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC411J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2208A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7193MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
- Undersize mm: 0.25 ;
|
MAHLE / CLEVITE : MS2208H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC322J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2202A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7296MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
- Undersize Inch: 0.025 ;
|
MAHLE / CLEVITE : MS2202P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2202H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC170J |
Crankshaft Main Bearing |
- Maximum Housing Inside Diameter: 2.8503-2.8513 ;
- Position: 1-2-3-4 ;
- Shaft Diameter: 2.6575 ;
- Shell Part Number: MB3947AU/L ;
- Width: 0.940 ;
|
MAHLE / CLEVITE : MS2207A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7297MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
|
MAHLE / CLEVITE : MS2295P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2295HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2295H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2259HXC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2259H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2259HC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS1812A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS1812P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2293H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2367A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2293HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7289MA |
Crankshaft Main Bearing |
- Part Material: A-Series aluminum ;
|
SEALED POWER : 7262MA |
Crankshaft Main Bearing |
- Part Alert: 0.002" O/S OD ;
- Part Material: A-Series aluminum ;
- Undersize Inch: 0.025 ;
- Undersize mm: 0.25 ;
|
ENGINETECH : BC420J |
Crankshaft Main Bearing |
|
SEALED POWER : 7295MA |
Crankshaft Main Bearing |
- Part Alert: Regrinding crank more than .50mm not recommended ;
- Part Material: A-Series aluminum ;
|
ENGINETECH : BC260J |
Crankshaft Main Bearing |
|
SEALED POWER : 153M |
Crankshaft Main Bearing |
|
ENGINETECH : BC172J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2344HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2344H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC036J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2034P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7325M |
Crankshaft Main Bearing |
- Part Material: Steel backed overplated bronze alloy ;
|
MAHLE / CLEVITE : MS2034HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2034H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC186J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS1706A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC373J |
Crankshaft Main Bearing |
|
SEALED POWER : 6695MA |
Crankshaft Main Bearing |
- Design Feature 1: 3/4 grooved ;
|
MAHLE / CLEVITE : MS1706P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7193M |
Crankshaft Main Bearing |
|
SEALED POWER : 158M |
Crankshaft Main Bearing |
|
SEALED POWER : 149M |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2269P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2381P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|