ENGINETECH : CC457 |
Balance Shaft Bearing |
|
SEALED POWER : 1892M |
Balance Shaft Bearing |
- Part Alert: For shafts in crankcase; Front drive bushing not incl. ;
- Part Material: Babbitt ;
|
MAHLE / CLEVITE : SH2008S |
Balance Shaft Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : CC455 |
Balance Shaft Bearing |
- Housing Bore: 2.1915-2.1925 ;
- Oil Clearance: 0.0012-0.0052 ;
- Position: 1-2 ;
- Shaft Diameter: 2.0505-2.0515 ;
- Shell Part Number: 284 ;
- Standard Or Oversized: Std ;
- Wall Thickness: 0.0694 ;
- Width Outer Ring: 0.640 ;
|
MAHLE / CLEVITE : SH1526S |
Balance Shaft Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 1807M |
Balance Shaft Bearing |
|