VOLKSWAGEN生产的Connecting Rod Bearing-第三方配件-宜配网-专业汽配网

也可拖拽图片到此处自动识别，或在微信/QQ截图后点击此处后Ctrl+V

参考号	零件	参数
ENGINETECH : BB1216	Connecting Rod Bearing
MAHLE / CLEVITE : CB1824A	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 6B1006	Connecting Rod Bearing
MAHLE / CLEVITE : CB1824A6	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1426A	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1426P	Connecting Rod Bearing	1.8802: 1.881 ; Min Shaft: Max Shaft ;
ITM ENGINE COMPONENTS : 4B9635	Connecting Rod Bearing
ENGINETECH : BB1215	Connecting Rod Bearing	Housing Bore: 1.9941-1.9949 in ; Number of Bearings: 4 ; Oil Clearance: 0.0008-0.0025 in ; Shaft Diameter: 1.8802-1.8810 in ; Width: 0.745 IN ;
ENGINETECH : BB1031	Connecting Rod Bearing	Housing Bore: 1.9921-1.9929 in ; Number of Bearings: 4 ; Oil Clearance: 0.0008-0.0025 in ; Shaft Diameter: 1.8802-1.8810 in ; Width: 0.745 IN ;
SEALED POWER : 44465P	Connecting Rod Bearing	Housing Bore Max (MM): 50.6120 ; Housing Bore Max (in): 1.9926 ; Housing Bore Min (MM): 50.5990 ; Housing Bore Min (in): 1.9921 ; Oil Clearance Max (MM): 0.0660 ; Oil Clearance Max (in): 0.0026 ; Oil Clearance Min (MM): 0.0200 ; Oil Clearance Min (in): 0.0008 ; Overall Length Max (MM): 19.0000 ; Overall Length Max (in): 0.7480 ; Standard Shaft Max (MM): 47.7770 ; Standard Shaft Max (in): 1.8810 ; Standard Shaft Min (MM): 47.7570 ; Standard Shaft Min (in): 1.8802 ; Wall Thickness Max (IN): 0.0553 ; Wall thickness Max (MM): 1.4050 ;
MAHLE / CLEVITE : CB1426A4	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1426HX	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1822P4	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ITM ENGINE COMPONENTS : 4B9649	Connecting Rod Bearing
MAHLE / CLEVITE : CB1822P	Connecting Rod Bearing	1.8802: 1.881 ; Min Shaft: Max Shaft ;
SEALED POWER : 6000A	Connecting Rod Bearing	Housing Bore Max (MM): 62.186 ; Housing Bore Min (MM): 62.174 ; Oil Clearance Max (MM): 0.061 ; Oil Clearance Min (MM): 0.011 ; Overall Length Max (MM): 17.90 ; Overall Length Min (MM): 17.64 ; Standard Shaft Max (MM): 59.009 ; Standard Shaft Min (MM): 58.991 ; Wall thickness Max (MM): 1.577 ;
SEALED POWER : 66000A	Connecting Rod Bearing	Housing Bore Max (MM): 62.186 ; Housing Bore Min (MM): 62.174 ; Oil Clearance Max (MM): 0.061 ; Oil Clearance Min (MM): 0.011 ; Overall Length Max (MM): 17.90 ; Overall Length Min (MM): 17.64 ; Standard Shaft Max (MM): 59.009 ; Standard Shaft Min (MM): 58.991 ; Wall thickness Max (MM): 1.577 ;
MAHLE / CLEVITE : CB1410A	Connecting Rod Bearing	2.283: 2.284 ; Min Shaft: Max Shaft ;
MAHLE / CLEVITE : CB1887A	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1887A6	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1410A6	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BB1223	Connecting Rod Bearing	Housing Bore: 2.2677-2.2682 in ; Number of Bearings: 6 ; Oil Clearance: 0.0006-0.0024 in ; Shaft Diameter: 2.1243-2.1251 in ;
MAHLE / CLEVITE : CB1881A	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
MAHLE / CLEVITE : CB1881A6	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BB139J	Connecting Rod Bearing	Housing Bore: 2.4013-2.4018 in ; Number of Bearings: 6 ; Oil Clearance: 0.0004-0.0022 in ; Shaft Diameter: 2.2828-2.2835 in ; Wall Thickness: 0.0582-0.0587 in ; Width: 0.685 in ;
MAHLE / CLEVITE : CB1426H	Connecting Rod Bearing	A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; D Bearing has dowel hole.: S Indicates a set number designation. ; G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;
ENGINETECH : BB175J	Connecting Rod Bearing	Housing Bore: 2.4470-2.4480 in ; Number of Bearings: 6 ; Oil Clearance: 0.0009-0.0025 in ; Shaft Diameter: 2.3220-2.3230 in ; Wall Thickness: 0.0617-0.0622 in ; Width: 0.700 in ;
ITM ENGINE COMPONENTS : 4B9630	Connecting Rod Bearing
ITM ENGINE COMPONENTS : 6B9320	Connecting Rod Bearing
SEALED POWER : 66015A	Connecting Rod Bearing	Note: Aluminum ;
ENGINETECH : BB1211	Connecting Rod Bearing	Housing Bore: 1.9921-1.9929 in ; Number of Bearings: 4 ; Oil Clearance: 0.0008-0.0025 in ; Shaft Diameter: 1.8802-1.8810 in ; Width: 0.745 IN ;

参考号

零件

参数

ENGINETECH : BB1216

Connecting Rod Bearing

MAHLE / CLEVITE : CB1824A

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 6B1006

Connecting Rod Bearing

MAHLE / CLEVITE : CB1824A6

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1426A

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1426P

Connecting Rod Bearing

1.8802: 1.881 ;
Min Shaft: Max Shaft ;

ITM ENGINE COMPONENTS : 4B9635

Connecting Rod Bearing

ENGINETECH : BB1215

Connecting Rod Bearing

Housing Bore: 1.9941-1.9949 in ;
Number of Bearings: 4 ;
Oil Clearance: 0.0008-0.0025 in ;
Shaft Diameter: 1.8802-1.8810 in ;
Width: 0.745 IN ;

ENGINETECH : BB1031

Connecting Rod Bearing

Housing Bore: 1.9921-1.9929 in ;
Number of Bearings: 4 ;
Oil Clearance: 0.0008-0.0025 in ;
Shaft Diameter: 1.8802-1.8810 in ;
Width: 0.745 IN ;

SEALED POWER : 44465P

Connecting Rod Bearing

Housing Bore Max (MM): 50.6120 ;
Housing Bore Max (in): 1.9926 ;
Housing Bore Min (MM): 50.5990 ;
Housing Bore Min (in): 1.9921 ;
Oil Clearance Max (MM): 0.0660 ;
Oil Clearance Max (in): 0.0026 ;
Oil Clearance Min (MM): 0.0200 ;
Oil Clearance Min (in): 0.0008 ;
Overall Length Max (MM): 19.0000 ;
Overall Length Max (in): 0.7480 ;
Standard Shaft Max (MM): 47.7770 ;
Standard Shaft Max (in): 1.8810 ;
Standard Shaft Min (MM): 47.7570 ;
Standard Shaft Min (in): 1.8802 ;
Wall Thickness Max (IN): 0.0553 ;
Wall thickness Max (MM): 1.4050 ;

MAHLE / CLEVITE : CB1426A4

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1426HX

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1822P4

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ITM ENGINE COMPONENTS : 4B9649

Connecting Rod Bearing

MAHLE / CLEVITE : CB1822P

Connecting Rod Bearing

1.8802: 1.881 ;
Min Shaft: Max Shaft ;

SEALED POWER : 6000A

Connecting Rod Bearing

Housing Bore Max (MM): 62.186 ;
Housing Bore Min (MM): 62.174 ;
Oil Clearance Max (MM): 0.061 ;
Oil Clearance Min (MM): 0.011 ;
Overall Length Max (MM): 17.90 ;
Overall Length Min (MM): 17.64 ;
Standard Shaft Max (MM): 59.009 ;
Standard Shaft Min (MM): 58.991 ;
Wall thickness Max (MM): 1.577 ;

SEALED POWER : 66000A

Connecting Rod Bearing

Housing Bore Max (MM): 62.186 ;
Housing Bore Min (MM): 62.174 ;
Oil Clearance Max (MM): 0.061 ;
Oil Clearance Min (MM): 0.011 ;
Overall Length Max (MM): 17.90 ;
Overall Length Min (MM): 17.64 ;
Standard Shaft Max (MM): 59.009 ;
Standard Shaft Min (MM): 58.991 ;
Wall thickness Max (MM): 1.577 ;

MAHLE / CLEVITE : CB1410A

Connecting Rod Bearing

2.283: 2.284 ;
Min Shaft: Max Shaft ;

MAHLE / CLEVITE : CB1887A

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1887A6

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1410A6

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BB1223

Connecting Rod Bearing

Housing Bore: 2.2677-2.2682 in ;
Number of Bearings: 6 ;
Oil Clearance: 0.0006-0.0024 in ;
Shaft Diameter: 2.1243-2.1251 in ;

MAHLE / CLEVITE : CB1881A

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

MAHLE / CLEVITE : CB1881A6

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;

ENGINETECH : BB139J

Connecting Rod Bearing

Housing Bore: 2.4013-2.4018 in ;
Number of Bearings: 6 ;
Oil Clearance: 0.0004-0.0022 in ;
Shaft Diameter: 2.2828-2.2835 in ;
Wall Thickness: 0.0582-0.0587 in ;
Width: 0.685 in ;

MAHLE / CLEVITE : CB1426H

Connecting Rod Bearing

A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ;
B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
D Bearing has dowel hole.: S Indicates a set number designation. ;
G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ;
HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ;
K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ;