t a  e 
参考号 零件 参数
ITM ENGINE COMPONENTS : 4B2024 Connecting Rod Bearing
MAHLE / CLEVITE : CB1808A Connecting Rod Bearing
  • 2.1257: 2.1263 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1808P Connecting Rod Bearing
  • 2.1257: 2.1263 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1808HN Connecting Rod Bearing
  • 2.1257: 2.1263 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1808HXN Connecting Rod Bearing
  • 2.1257: 2.1263 ; 
  • Min Shaft: Max Shaft ; 
ENGINETECH : BB181J Connecting Rod Bearing
  • Housing Bore: 2.2522-2.2527 in ; 
  • Number of Bearings: 8 ; 
  • Oil Clearance: 0.0008-0.0029 in ; 
  • Shaft Diameter: 2.1257-2.1263 in ; 
  • Wall Thickness: 0.0631-0.0636 in ; 
  • Width: 0.791 IN ; 
MAHLE / CLEVITE : CB1808A8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB111J Connecting Rod Bearing
  • Housing Bore: 2.2522-2.2527 in ; 
  • Number of Bearings: 8 ; 
  • Oil Clearance: 0.0008-0.0029 in ; 
  • Shaft Diameter: 2.1257-2.1263 in ; 
  • Wall Thickness: 0.0621-0.0626 in ; 
  • Width: 0.791 IN ; 
MAHLE / CLEVITE : CB1809A8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1808P8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 84960P Connecting Rod Bearing
  • Housing Bore Max (MM): 57.2190 ; 
  • Housing Bore Max (in): 2.2527 ; 
  • Housing Bore Min (MM): 57.2060 ; 
  • Housing Bore Min (in): 2.2522 ; 
  • Oil Clearance Max (MM): 0.0740 ; 
  • Oil Clearance Max (in): 0.0029 ; 
  • Oil Clearance Min (MM): 0.0200 ; 
  • Oil Clearance Min (in): 0.0008 ; 
  • Overall Length Max (MM): 20.0900 ; 
  • Overall Length Max (in): 0.7910 ; 
  • Standard Shaft Max (MM): 54.0080 ; 
  • Standard Shaft Max (in): 2.1263 ; 
  • Standard Shaft Min (MM): 53.9930 ; 
  • Standard Shaft Min (in): 2.1257 ; 
  • Wall Thickness Max (IN): 0.0626 ; 
  • Wall thickness Max (MM): 1.5900 ; 
SEALED POWER : 6000A Connecting Rod Bearing
  • Housing Bore Max (MM): 62.186 ; 
  • Housing Bore Min (MM): 62.174 ; 
  • Oil Clearance Max (MM): 0.061 ; 
  • Oil Clearance Min (MM): 0.011 ; 
  • Overall Length Max (MM): 17.90 ; 
  • Overall Length Min (MM): 17.64 ; 
  • Standard Shaft Max (MM): 59.009 ; 
  • Standard Shaft Min (MM): 58.991 ; 
  • Wall thickness Max (MM): 1.577 ; 
SEALED POWER : 66000A Connecting Rod Bearing
  • Housing Bore Max (MM): 62.186 ; 
  • Housing Bore Min (MM): 62.174 ; 
  • Oil Clearance Max (MM): 0.061 ; 
  • Oil Clearance Min (MM): 0.011 ; 
  • Overall Length Max (MM): 17.90 ; 
  • Overall Length Min (MM): 17.64 ; 
  • Standard Shaft Max (MM): 59.009 ; 
  • Standard Shaft Min (MM): 58.991 ; 
  • Wall thickness Max (MM): 1.577 ; 
MAHLE / CLEVITE : CB1957A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1813A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 4565AA Connecting Rod Bearing
  • Housing Bore Max (MM): 53.007 ; 
  • Housing Bore Max (in): 2.0869 ; 
  • Housing Bore Min (MM): 52.995 ; 
  • Housing Bore Min (in): 2.0864 ; 
  • Oil Clearance Max (MM): 0.071 ; 
  • Oil Clearance Max (in): 0.0028 ; 
  • Oil Clearance Min (MM): 0.025 ; 
  • Oil Clearance Min (in): 0.0010 ; 
  • Overall Length Max (MM): 20.170 ; 
  • Overall Length Max (in): 0.7940 ; 
  • Standard Shaft Max (MM): 50.000 ; 
  • Standard Shaft Max (in): 1.9685 ; 
  • Standard Shaft Min (MM): 49.985 ; 
  • Standard Shaft Min (in): 1.9679 ; 
  • Wall Thickness Max (IN): 0.0584 ; 
  • Wall thickness Max (MM): 1.483 ; 
MAHLE / CLEVITE : CB1813H Connecting Rod Bearing
  • 1.9677: 1.9687 ; 
  • Min Shaft: Max Shaft ; 
ENGINETECH : BB308J Connecting Rod Bearing
  • Housing Bore: 2.0864-2.0869 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0010-0.0028 in ; 
  • Shaft Diameter: 1.9679-1.9685 in ; 
  • Wall Thickness: 0.0579-0.0584 in ; 
  • Width: 0.789 in ; 
MAHLE / CLEVITE : CB1813A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1410A Connecting Rod Bearing
  • 2.283: 2.284 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1887A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 1920RA Connecting Rod Bearing
  • Housing Bore Max (MM): 61.0080 ; 
  • Housing Bore Max (in): 2.4019 ; 
  • Housing Bore Min (MM): 60.9920 ; 
  • Housing Bore Min (in): 2.4013 ; 
  • Oil Clearance Max (MM): 0.0760 ; 
  • Oil Clearance Max (in): 0.0030 ; 
  • Oil Clearance Min (MM): 0.0180 ; 
  • Oil Clearance Min (in): 0.0007 ; 
  • Overall Length Max (MM): 16.5400 ; 
  • Overall Length Max (in): 0.6510 ; 
  • Standard Shaft Max (MM): 58.0050 ; 
  • Standard Shaft Max (in): 2.2836 ; 
  • Standard Shaft Min (MM): 57.9790 ; 
  • Standard Shaft Min (in): 2.2827 ; 
  • Wall Thickness Max (IN): 0.0584 ; 
  • Wall thickness Max (MM): 1.4840 ; 
ENGINETECH : BB638J Connecting Rod Bearing
  • Housing Bore: 2.4012-2.4019 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0007-0.0030 in ; 
  • Shaft Diameter: 2.2826-2.2837 in ; 
  • Wall Thickness: 0.0579-0.0584 in ; 
  • Width: 0.651 IN ; 
MAHLE / CLEVITE : CB1887A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 61920RA Connecting Rod Bearing
  • Housing Bore Max (MM): 61.0080 ; 
  • Housing Bore Max (in): 2.4019 ; 
  • Housing Bore Min (MM): 60.9900 ; 
  • Housing Bore Min (in): 2.4013 ; 
  • Oil Clearance Max (MM): 0.0760 ; 
  • Oil Clearance Max (in): 0.0030 ; 
  • Oil Clearance Min (MM): 0.0180 ; 
  • Oil Clearance Min (in): 0.0007 ; 
  • Overall Length Max (MM): 16.5400 ; 
  • Overall Length Max (in): 0.6510 ; 
  • Standard Shaft Max (MM): 58.0060 ; 
  • Standard Shaft Max (in): 2.2836 ; 
  • Standard Shaft Min (MM): 57.9780 ; 
  • Standard Shaft Min (in): 2.2827 ; 
  • Wall Thickness Max (IN): 0.0584 ; 
  • Wall thickness Max (MM): 1.4830 ; 
MAHLE / CLEVITE : CB1410A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1855A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1784P Connecting Rod Bearing
  • 2.0075: 2.0082 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1854A8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 84835A Connecting Rod Bearing
  • Oil Clearance Max (MM): 0.0460 ; 
  • Oil Clearance Max (in): 0.0018 ; 
  • Oil Clearance Min (MM): 0.0100 ; 
  • Oil Clearance Min (in): 0.0004 ; 
  • Overall Length Max (MM): 16.6400 ; 
  • Overall Length Max (in): 0.6550 ; 
  • Standard Shaft Max (MM): 51.0030 ; 
  • Standard Shaft Max (in): 2.0080 ; 
  • Standard Shaft Min (MM): 50.9960 ; 
  • Standard Shaft Min (in): 2.0077 ; 
  • Wall Thickness Max (IN): 0.0587 ; 
  • Wall thickness Max (MM): 1.4910 ; 
MAHLE / CLEVITE : CB1804A8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1784P8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1784A8 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1670A Connecting Rod Bearing
  • 2.1059: 2.1067 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1787A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB307J Connecting Rod Bearing
  • Housing Bore: 2.2261-2.2267 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0005-0.0030 in ; 
  • Shaft Diameter: 2.1060-2.1070 in ; 
  • Wall Thickness: 0.0590-0.0595 in ; 
  • Width: 0.684 IN ; 
ENGINETECH : BB423J Connecting Rod Bearing
  • Housing Bore: 2.2241-2.2247 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0005-0.0030 in ; 
  • Shaft Diameter: 2.1060-2.1070 in ; 
  • Wall Thickness: 0.0580-0.0585 in ; 
  • Width: 0.684 IN ; 
MAHLE / CLEVITE : CB1670A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1787A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1881A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 64845P Connecting Rod Bearing
  • Housing Bore Max (MM): 61.0060 ; 
  • Housing Bore Max (in): 2.4018 ; 
  • Housing Bore Min (MM): 60.9930 ; 
  • Housing Bore Min (in): 2.4013 ; 
  • Note: Tri-metal ; 
  • Oil Clearance Max (MM): 0.0810 ; 
  • Oil Clearance Max (in): 0.0032 ; 
  • Oil Clearance Min (MM): 0.0180 ; 
  • Oil Clearance Min (in): 0.0007 ; 
  • Overall Length Max (MM): 16.9700 ; 
  • Overall Length Max (in): 0.6680 ; 
  • Standard Shaft Max (MM): 58.0060 ; 
  • Standard Shaft Max (in): 2.2837 ; 
  • Standard Shaft Min (MM): 57.9780 ; 
  • Standard Shaft Min (in): 2.2826 ; 
  • Wall Thickness Max (IN): 0.0585 ; 
  • Wall thickness Max (MM): 1.4860 ; 
MAHLE / CLEVITE : CB1881A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB139J Connecting Rod Bearing
  • Housing Bore: 2.4013-2.4018 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0004-0.0022 in ; 
  • Shaft Diameter: 2.2828-2.2835 in ; 
  • Wall Thickness: 0.0582-0.0587 in ; 
  • Width: 0.685 in ; 
SEALED POWER : 64830A Connecting Rod Bearing
  • Oil Clearance Max (MM): 0.0640 ; 
  • Oil Clearance Max (in): 0.0025 ; 
  • Oil Clearance Min (MM): 0.0130 ; 
  • Oil Clearance Min (in): 0.0005 ; 
  • Overall Length Max (MM): 17.4800 ; 
  • Overall Length Max (in): 0.6880 ; 
MAHLE / CLEVITE : CB1669A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1669P Connecting Rod Bearing
  • 2.2826: 2.2837 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1880P Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB103J Connecting Rod Bearing
  • Housing Bore: 2.4013-2.4018 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0008-0.0034 in ; 
  • Shaft Diameter: 2.2826-2.2837 in ; 
  • Wall Thickness: 0.0579-0.0584 in ; 
  • Width: 0.684 IN ; 
MAHLE / CLEVITE : CB1669A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1669P6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ITM ENGINE COMPONENTS : 4B1215 Connecting Rod Bearing
ENGINETECH : BB1827 Connecting Rod Bearing
  • Housing Bore: 1.8898-1.8904 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0020 in ; 
  • Shaft Diameter: 1.7709-1.7717 in ; 
  • Wall Thickness: 0.0582-0.0587 ; 
  • Width: 0.827 IN ; 
ENGINETECH : BB167J Connecting Rod Bearing
  • Housing Bore: 2.0078-2.0084 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0008-0.0027 in ; 
  • Shaft Diameter: 1.8879-1.8886 in ; 
  • Wall Thickness: 0.0588-0.0593 in ; 
  • Width: 0.630 in ; 
MAHLE / CLEVITE : CB1909A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1643P Connecting Rod Bearing
  • 1.771: 1.7717 ; 
  • Min Shaft: Max Shaft ; 
MAHLE / CLEVITE : CB1643H Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1643HX Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1643A4 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB175J Connecting Rod Bearing
  • Housing Bore: 2.4470-2.4480 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0009-0.0025 in ; 
  • Shaft Diameter: 2.3220-2.3230 in ; 
  • Wall Thickness: 0.0617-0.0622 in ; 
  • Width: 0.700 in ; 
ENGINETECH : BB327J Connecting Rod Bearing
  • Housing Bore: 2.0884-2.0889 in ; 
  • Number of Bearings: 4 ; 
  • Oil Clearance: 0.0010-0.0028 in ; 
  • Shaft Diameter: 1.9688-1.9695 in ; 
  • Wall Thickness: 0.0588-0.0593 in ; 
  • Width: 0.794 ; 
SEALED POWER : 66015A Connecting Rod Bearing
  • Note: Aluminum ; 
ITM ENGINE COMPONENTS : 4B9653 Connecting Rod Bearing
MAHLE / CLEVITE : CB1411A Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1411H Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
MAHLE / CLEVITE : CB1411HX Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
ENGINETECH : BB634J Connecting Rod Bearing
  • Housing Bore: 2.0866-2.0874 in ; 
  • Number of Bearings: 6 ; 
  • Oil Clearance: 0.0006-0.0035 in ; 
  • Shaft Diameter: 1.9674-1.9685 in ; 
  • Wall Thickness: 0.0583-0.0587 in ; 
  • Width: 0.601 in ; 
MAHLE / CLEVITE : CB1411A6 Connecting Rod Bearing
  • A Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ; 
  • AL Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N Narrowed for greater crankshaft fillet clearance. ; 
  • B Steel backed bearings with a conventional babbit lining.: P Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ; 
  • C Steel backed bearings with a copper-lead lining.: R Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ; 
  • D Bearing has dowel hole.: S Indicates a set number designation. ; 
  • G Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ; 
  • H High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ; 
  • HG High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X Bearing has .001” more oil clearance than standard. ; 
  • HT High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX Bearing has .002” more oil clearance than standard. ; 
  • K TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W Indicates a part that is a thrust washer (may also be designated upper or lower). ; 
SEALED POWER : 61735CP Connecting Rod Bearing
  • Housing Bore Max (MM): 53.0200 ; 
  • Housing Bore Max (in): 2.0874 ; 
  • Housing Bore Min (MM): 53.0000 ; 
  • Housing Bore Min (in): 2.0866 ; 
  • Oil Clearance Max (MM): 0.0890 ; 
  • Oil Clearance Max (in): 0.0035 ; 
  • Oil Clearance Min (MM): 0.0150 ; 
  • Oil Clearance Min (in): 0.0006 ; 
  • Overall Length Max (MM): 15.3900 ; 
  • Overall Length Max (in): 0.6060 ; 
  • Standard Shaft Max (MM): 50.0000 ; 
  • Standard Shaft Max (in): 1.9685 ; 
  • Standard Shaft Min (MM): 49.9720 ; 
  • Standard Shaft Min (in): 1.9674 ; 
  • Wall Thickness Max (IN): 0.0587 ; 
  • Wall thickness Max (MM): 1.4910 ; 
SEALED POWER : 4615P Connecting Rod Bearing
  • Housing Bore Max (MM): 51.0060 ; 
  • Housing Bore Max (in): 2.0081 ; 
  • Housing Bore Min (MM): 50.9910 ; 
  • Housing Bore Min (in): 2.0075 ; 
  • Oil Clearance Max (MM): 0.0610 ; 
  • Oil Clearance Max (in): 0.0024 ; 
  • Oil Clearance Min (MM): 0.0200 ; 
  • Oil Clearance Min (in): 0.0008 ; 
  • Overall Length Max (MM): 20.4700 ; 
  • Overall Length Max (in): 0.8060 ; 
  • Standard Shaft Max (MM): 48.0060 ; 
  • Standard Shaft Max (in): 1.8900 ; 
  • Standard Shaft Min (MM): 47.9910 ; 
  • Standard Shaft Min (in): 1.8894 ; 
  • Wall Thickness Max (IN): 0.0584 ; 
  • Wall thickness Max (MM): 1.4830 ; 
[1]
共
69
条记录，分
1
页显示
按品牌拼音首字母查找：

      尺寸/参数

      标注 名称 尺寸范围 单位
          

      标注实例

      联系客服

      客服电话：020-36390347